Q1. Refer to the Exhibit:

Which two statements correctly indicates when an SNMP trap is sent to the switch? (Choose Two)

A. When a new workstation connects to port F0/1

B. When 61 MAC address are in the switch

C. When 61 percent of the Address table capacity is used

D. When the switch loses power and reboots

E. When the phone previously on Fa0/2 is now connect to Fa0/5

Q2. After an EtherChannel is configured between two Cisco switches, interface port channel 1 is in the down/down state. Switch A is configured with channel-group 1 mode active, while Switch B is configured with channel-group 1 mode desirable. Why is the EtherChannel bundle not working?

A. The switches are using mismatched EtherChannel negotiation modes.

B. The switch ports are not configured in trunking mode.

C. LACP priority must be configured on both switches.

D. The channel group identifier must be different for Switch A and Switch B.

Q3. What are the possible results of port-security?

A. error disable (shut down)

B. send a trap

C. port disabled

D. loop inconsistant

Q4. An engineer is configuring an EtherChannel between two switches using LACP. If the EtherChannel mode on switch 1 is configured to active, which two modes on switch 2 establish an operational EtherChannel? (Choose two.)

A. active

B. auto

C. desirable

D. on

E. passive

Q5. Which option describes a limitation of LLDP?

A. LLDP cannot provide information about VTP.

B. LLDP does not support TLVs.

C. LLDP can discover only Windows servers.

D. LLDP can discover up to two devices per port.

Q6. While troubleshooting a network outage, a network engineer discovered an unusually high level of broadcast traffic coming from one of the switch interfaces. Which option decreases consumption of bandwidth used by broadcast traffic?

A. storm control

B. SDM routing

C. Cisco IOS parser

D. integrated routing and bridging

E. Dynamic ARP Inspection

Q7. Your manager asked you to make every port on your switch bypass the normal spanning- tree timers which

includes your uplink to other switches. What two commands can you apply on the interfaces? (Choose two.)

A. spanning-tree portfast

B. spanning-tree portfast default

C. spanning-tree portfast access

D. spanning-tree portfast trunk

Q8. Which command would a network engineer apply to error-disable a switchport when a packet-storm is detected?

A. router(config-if)#storm-control action shutdown

B. router(config-if)#storm-control action trap

C. router(config-if)#storm-control action error

D. router(config-if)#storm-control action enable

Q9. After reviewing UDLD status on switch ports, an engineer notices that the." Which statement describes what this indicates about the status of the port?

A. The port is fully operational and no known issues are detected.

B. The bidirectional status of "unknown" indicates that the port will go into the disabled state because it stopped receiving UDLD packets from its neighbor.

C. UDLD moved into aggressive mode after inconsistent acknowledgements were detected.

D. The UDLD port is placed in the "unknown" state for 5 seconds until the next UDLD packet is received on the interface.

Q10. Refer to the exhibit.

***Missing Exhibit***

Which statement describes the result if a switch that is running PVST+ is added to this network?

A. Spanning tree is disabled automatically on the network

B. Spanning tree continues to operate in Rapid PVST+ on DSW2 and the new switch operates in PVST+

C. Both switches operate in the PVST+ mode

D. Both switches operate in the Rapid PVST+ mode

Q11. Refer to the exhibit.

Which configuration on the HSRP neighboring device ensures that it becomes the active HSRP device in the event that port fa1/1 on Switch_A goes down?

A. Switch_B(config-if)#ip address 10.10.10.2 255.255.255.0

Switch_B(config-if)#standby 1 priority 200

Switch_B(config-if)#standby 1 preempt

Switch_B(config-if)#standby 1 ip 10.10.10.10 Switch_B(config-if)#standby 1 track interface fa 1/1

B. Switch_B(config-if)#ip address 10.10.10.2 255.255.255.0

Switch_B(config-if)#standby 1 priority 200

Switch_B(config-if)#standby 1 ip 10.10.10.10

C. Switch_B(config-if)#ip address 10.10.10.2 255.255.255.0

Switch_B(config-if)#standby 1 priority 195

Switch_B(config-if)#standby 1 preempt

Switch_B(config-if)#standby 1 ip 10.10.10.10

D. Switch_B(config-if)#ip address 10.10.10.2 255.255.255.0

Switch_B(config-if)#standby 1 priority 190

Switch_B(config-if)#standby 1 ip 10.10.10.10 Switch_B(config-if)#standby 1 track interface fa 1/1