NEW QUESTION 1
NAPT allows for multiple internal addresses to be mapped to a single public address. How does NATdistinguish between the different private addresses when mapping to the same public address?

• A. The source MAC address is used.
• B. The destination MAC address is used.
• C. The source port number is used.
• D. The destination port number is used.

Answer: C

NEW QUESTION 2
An ARP request is sent by host A to obtain the destination MAC address of host D. Which statement is trueabout regarding the ARP reply?

• A. The destination MAC address of this frame is the MAC address of Switch A.
• B. The destination IP address of this packet is the VLANIF1 IP address of Switch A.
• C. The destination MAC address of this frame is the MAC address of Host A.
• D. The destination IP address of this packet is a broadcast IP address.

Answer: C

NEW QUESTION 3
[R1]display interface GigabitEthernet0/0/0 GigabitEthernet0/0/0 current state : Administratively DOWN Line protocol current state : DOWN
Refer to the display output. What can be determined based on the output of the display command?

• A. Interface Gigabit Ethernet 0/0/0 is connected to a wrong cable
• B. Interface Gigabit Ethernet 0/0/0 is not associated with an IP address
• C. Interface Gigabit Ethernet 0/0/0 is not associated with a dynamically defined route.
• D. Interface Gigabit Ethernet 0/0/0 has been manually shut down by an administrator.

Answer: D

NEW QUESTION 4
The network administrator wishes to transmit data between two endstations. The network interfacecards ofboth devices operates at 100Mbps however one supports half duplex while the other uses full duplex mode.
What will occur as a result?

• A. The end stations cannot communicate.
• B. The end stations can communicate, but data may be lost during transmission of large amounts of traffic.
• C. The end stations will operate normally
• D. The end stations can communicate, but speed is different during transmission of large amounts of traffic.

Answer: B

NEW QUESTION 5
A client failed to transfer a file to the FTP server, but found the IP connectivity was without problem. The clientassumed that the problem was with the port configuration. The blocking of which ports wouldlikely cause thisproblem?(Choose two)

• A. 21
• B. 80
• C. 20
• D. 50649

Answer: AC

NEW QUESTION 6
An administrator wishes to implement new features in the network, but the VRP version of one AR2200 routeris out of date. Theadministratorneeds to upgrade the VRP software. Which of the following options regardingfile transfer is false?

• A. The AR2200 router can function as a TFTP client to support the upgrade.
• B. The AR2200 router can function as the TFTP server to support the upgrade.
• C. The AR2200 router can function as the FTP server to support the upgrade.
• D. The AR2200 router can function as an FTP client to support the upgrade.

Answer: B

NEW QUESTION 7
In order to check if the interface serial 1/0/0 is working in either DCE or DTE mode, command ( ) is used.

• A. display mode serial 1/0/0
• B. display controller
• C. display interface serial 1/0/0
• D. display current-config

Answer: C

NEW QUESTION 8
How is mapping performed on a DTE device in a Frame Relay network?

• A. The local DLCI number is mapped to a remote IP address.
• B. The local IP address is mapped to a remote DLCI number.
• C. The local DLCI number is mapped to a local IP address.
• D. The remote DLCI number is mapped to a remote IP address.

Answer: A

NEW QUESTION 9
Which of the following statements about a designated port working in RIPv2 multicast mode are true?(Choose three)

• A. The port receives only RIPv2 multicast packets.
• B. The port does not receive RIPv1 broadcast packets.
• C. The port does not receive RIPv2 broadcast packets.
• D. The port receives only RIPv1 multicast packets.

Answer: ABC

NEW QUESTION 10
Which of the following parameters is not used by Advanced ACL?

• A. Source interface
• B. Destination port number
• C. Protocol number
• D. Time-range

Answer: A

NEW QUESTION 11
Refer to the grapic. An administrator has configured RIPv2 on the two routers, following which he implementsthe command silent-interface s0/0/1 on RTA. What effect will this command have on the network? (TwoAnswers)

• A. RTA will continue to learn routes from RTB
• B. RTB will continue to learn routes from RTA
• C. RTA will have no neighbor relationship with RTB
• D. RTB will have no adjacency relationship with RTA

Answer: AD

NEW QUESTION 12
The network administrator attempts to add interface G0/0/1 on Switch A to Eth-trunk 1, however the commandfails. Which of the following may cause this?

• A. The interface is operating in half-duplex mode.
• B. The interface has been shutdown.
• C. The interface is already associated with another Eth-trunk.
• D. The interface is an access port.

Answer: CD

NEW QUESTION 13
Which of the following descriptions regarding eSight is not correct?

• A. eSight is used to monitor and manage enterprise networks.
• B. eSight supports only Huawei devices
• C. eSight supports WLAN management and monitoring of hotspot coverage.
• D. eSight supports the backup of configuration files and network traffic analysis.

Answer: B

NEW QUESTION 14
[RTA]acl 2001
[RTA-acl-basic-2001]rule 20 permit source 20.1.1.0 0.0.0.255
[RTA-acl-basic-2001]rule 10 deny source 20.1.1.0 0.0.0.255
Refer to the configuration output. Which of the following statements is correct regarding the configuration of theACL on RTA?

• A. Packets from network 20.1.1.0/24 network will be denied.
• B. Packets from network 20.1.1.0/24 network will be permitted.
• C. Packets destined for network 20.1.1.0/24 will be denied.
• D. Packets destined for network 20.1.1.0/24 will be permitted.

Answer: A

NEW QUESTION 15
Refer to the graphic. An administrator has configed RIPv2 in the two routers shows in the figure. What willhappen after configuring the following commands? (Choose two)
[RTA-Serial0/0/1]rip output [RTA-rip-1]silent-interface s0/0/1

• A. RTA will have the route learned from the RTB
• B. RTB will have the route learn from the RTA
• C. RTA will have no neighbor relationship with RTB
• D. RTB will have no neighbor relationship with RTB

Answer: AD

NEW QUESTION 16
Which of the following statements regarding layer-2 switch is incorrect?

• A. The switch learns MAC addresses automatically
• B. The layer-3 header is modified before the received packet is transmitted
• C. The layer-2 header is modified before the received packet is transmitted.
• D. The layer-2 LAN switch operates at data link layer

Answer: B

NEW QUESTION 17
When a router is powered on, the router reads the configuration file saved in the default
save directory to getitself initialized. If the configuration file does not exist in the default save directory, what does the router use toinitialize itself?

• A. New configuration file
• B. Initial configuration file
• C. Default parameters
• D. Current configuration file

Answer: C

NEW QUESTION 18
In the case of Huawei router, what is the "-i" parameter in a Ping command issued on a VRP operating systemused to set?

• A. Interface for sending an Echo Request packet
• B. Source IP address for sending an Echo Request packet
• C. Interface for receiving an Echo Reply packet
• D. Destination IP address for receiving an Echo Reply packet

Answer: A

NEW QUESTION 19
The administrator wishes to manage a network through telnet from a user's terminal to a
router. How can thisbe achieved?

• A. A connection should be established between the ethernet port of the terminal and the console port of therouter.
• B. A connection should be established between the ethernet port of the terminal and the ethernet port of therouter.
• C. A connection should be established between the console port of the terminal and the ethernet port of therouter.use console cable connect pc’s ethernet port and router’s console port.
• D. A connection should be established between the COM port of the terminal and the console port of therouter.

Answer: B