200-105 Exam Questions - Online Test

200-105 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

Examcollection ccna routing and switching icnd2 200 105 official cert guide Questions are updated and all 200 105 icnd2 answers are verified by experts. Once you have completely prepared with our 105 200 exam prep kits you will be ready for the real ccna 200 105 exam without a problem. We have Up to the minute Cisco icnd2 200 105 dumps study guide. PASSED icnd2 200 105 First attempt! Here What I Did.

P.S. Virtual 200-105 interactive bootcamp are available on Google Drive, GET MORE: https://drive.google.com/open?id=15qdYN17ESAKqiw2FrpOPw3870_4rbe12

New Cisco 200-105 Exam Dumps Collection (Question 10 - Question 19)

Q1. Which feature does PPP use to encapsulate multiple protocols?

A. NCP

B. LCP

C. IPCP

D. IPXP

Answer: A

Explanation:

PPP permits multiple network layer protocols to operate on the same communication link. For every network layer protocol used, a separate Network Control Protocol (NCP) is provided in order to encapsulate and negotiate options for the multiple network layer protocols. It negotiates network-layer information, e.g. network address or compression options, after the connection has been established

Q2. Which feature facilitates the tagging of frames on a specific VLAN?

A. Routing

B. hairpinning

C. switching

D. encapsulation

Answer: D

Q3. Refer to the exhibit.

Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)

A. Host E and host F use the same IP gateway address.

B. Router1 and Switch2 should be connected via a crossover cable.

C. Router1 will not play a role in communications between host A and host D.

D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.

E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.

F. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type.

Answer: D,F

Explanation: http://www.cisco.com/en/US/tech/tk389/tk815/technologies_configuration_example09186a 00800949fd.shtml

Q4. A router receives information about network 192.168.10.0/24 from multiple sources. What will the router consider the most reliable information about the path to that network?

A. an OSPF update for network 192.168.0.0/16

B. a static route to network 192.168.10.0/24

C. a static route to network 192.168.10.0/24 with a local serial interface configured as the next hop

D. a RIP update for network 192.168.10.0/24

E. a directly connected interface with an address of 192.168.10.254/24

F. a default route with a next hop address of 192.168.10.1

Answer: E

Explanation:

What Is Administrative Distance? http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080094195.shtml

Select the Best Path

Administrative distance is the first criterion that a router uses to determine which routing protocol to use if two protocols provide route information for the same destination. Administrative distance is a measure of the trustworthiness of the source of the routing information. Administrative distance has only local significance, and is not advertised in routing updates.

Note: The smaller the administrative distance value, the more reliable the protocol. For example, if a router receives a route to a certain network from both Open Shortest Path First (OSPF) (default administrative distance - 110) and Interior Gateway Routing Protocol (IGRP) (default administrative distance - 100), the router chooses IGRP because IGRP is more reliable. This means the router adds the IGRP version of the route to the routing table.

Q5. Which statement about DTP is true?

A. It uses the native VLAN.

B. It negotiates a trunk link after VTP has been configured.

C. It uses desirable mode by default.

D. It sends data on VLAN 1.

Answer: A

Q6. Which feature can you use to restrict SNMP queries to a specific OID tree?

A. a server group

B. a view record

C. a community

D. an access group

Answer: C

Explanation: The Setup SNMP view command can block the user with only access to limited Management Information Base (MIB). By default, there is no SNMP view entry exists. This command is configured at the global configuration mode and first introduced in Cisco IOS Software version 10.3. It works similar to access-list in that if you have any SNMP View on certain MIB trees, every other tree is denied inexplicably. However, the sequence is not important and it goes through the entire list for a match before it stops.

Q7. What is the best way to verify that a host has a path to other hosts in different networks?

A. Ping the loopback address.

B. Ping the default gateway.

C. Ping the local interface address.

D. Ping the remote network.

Answer: D

Explanation:

Ping is a tool that helps to verify IP-level connectivity; PathPing is a tool that detects packet loss over multiple-hop trips. When troubleshooting, the ping command is used to send an ICMP Echo Request to a target host name or IP address. Use Ping whenever you want to verify that a host computer can send IP packets to a destination host. You can also use the Ping tool to isolate network hardware problems and incompatible configurations.

If you call ipconfig /all and receive a response, there is no need to ping the loopback address and your own IP address u2014 Ipconfig has already done so in order to generate the report.

It is best to verify that a route exists between the local computer and a network host by first using ping and the IP address of the network host to which you want to connect. The command syntax is:

ping < IP address >

Perform the following steps when using Ping:

u2711 Ping the loopback address to verify that TCP/IP is installed and configured correctly on the local computer.

ping 127.0.0.1

If the loopback step fails, the IP stack is not responding. This might be because the TCP drivers are corrupted, the network adapter might not be working, or another service is interfering with IP.

u2711 Ping the IP address of the local computer to verify that it was added to the network

correctly. Note that if the routing table is correct, this simply forwards the packet to the loopback address of 127.0.0.1.

ping < IP address of local host >

u2711 Ping the IP address of the default gateway to verify that the default gateway is functioning and that you can communicate with a local host on the local network.

ping < IP address of default gateway >

u2711 Ping the IP address of a remote host to verify that you can communicate through a router.

ping < IP address of remote host >

u2711 Ping the host name of a remote host to verify that you can resolve a remote host name.

ping < Host name of remote host >

u2711 Run a PathPing analysis to a remote host to verify that the routers on the way to

the destination are operating correctly. pathping < IP address of remote host >

Q8. Refer to the exhibit.

The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table on the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?

A. 10.0.0.0/22 is subnetted, 1 subnets

D 10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

B. 10.0.0.0/28 is subnetted, 1 subnets

D 10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

C. 10.0.0.0/30 is subnetted, 1 subnets

D 10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

D. 10.0.0.0/22 is subnetted, 1 subnets

D 10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

E. 10.0.0.0/28 is subnetted, 1 subnets

D 10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

F. 10.0.0.0/30 is subnetted, 1 subnets

D 10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

Answer: D

Explanation:

All the above networks can be summarized to 10.0.0.0 network but the question requires to u201crepresent the LANs in Phoenix but no additional subnetsu201d so we must summarized to

10.4.0.0 network. The Phoenix router has 4 subnets so we need to u201cmove leftu201d 2 bits of u201c/24-> /22 is the best choice - D is correct.

Q9. Which statement describes the process ID that is used to run OSPF on a router?

A. It is globally significant and is used to represent the AS number.

B. It is locally significant and is used to identify an instance of the OSPF database.

C. It is globally significant and is used to identify OSPF stub areas.

D. It is locally significant and must be the same throughout an area.

Answer: B

Explanation: The Process ID for OSPF on a router is only locally significant and you can use the same number on each router, or each router can have a different number-it just

doesn't matter. The numbers you can use are from 1 to 65,535. Don't get this confused with area numbers, which can be from 0 to 4.2 billion.

Q10. Refer to the exhibit.

What information about the interfaces on the Main_Campus router is true?

A. The LAN interfaces are configured on different subnets.

B. Interface FastEthernet 0/0 is configured as a trunk.

C. The Layer 2 protocol of interface Serial 0/1 is NOT operational.

D. The router is a modular router with five FastEthernet interfaces.

E. Interface FastEthernet 0/0 is administratively deactivated.

Answer: B

Explanation:

Interface fa0/0 breaks into sub-interfaces and Main_Campus router is connected with

switch via fa0/0 .Subinterfaces configured with different subnet masks so the same switch has multiple vlans and allows communication between these VLAN's. For routing and inter- vlan we need to configure a trunk port. So B will be the correct answer.

100% Up to the minute Cisco 200-105 Questions & Answers shared by Allfreedumps, Get HERE: https://www.allfreedumps.com/200-105-dumps.html (New 267 Q&As)