156-915.80 Exam Questions - Online Test

156-915.80 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

It is more faster and easier to pass the Check Point 156-915.80 exam by using Download Check Point Check Point Certified Security Expert Update - R80 questuins and answers. Immediate access to the Avant-garde 156-915.80 Exam and find the same core area 156-915.80 questions with professionally verified answers, then PASS your exam with a high score now.

P.S. Download 156-915.80 secret are available on Google Drive, GET MORE: https://drive.google.com/open?id=1YYqgCO6ctCwcBVUFbQYMfHPbrQOvemUT

New Check Point 156-915.80 Exam Dumps Collection (Question 8 - Question 16)

Question No: 8

You have three Gateways in a mesh community. Each gatewayu2021s VPN Domain is their internal network as defined on the Topology tab setting All IP Addresses behind Gateway based on Topology information.

You want to test the route-based VPN, so you created VTIs among the Gateways and created static route entries for the VTIs. However, when you test the VPN, you find out the VPN still go through the regular domain IPsec tunnels instead of the routed VTI tunnels.

What is the problem and how do you make the VPN use the VTI tunnels?

A. Domain VPN takes precedence over the route-based VTI. To make the VPN go through VTI, remove the Gateways out of the mesh community and replace with a star community

B. Domain VPN takes precedence over the route-based VTI. To make the VPN go through VTI, use an empty group object as each Gatewayu2021s VPN Domain

C. Route-based VTI takes precedence over the Domain VPN. To make the VPN go through VTI, use dynamic-routing protocol like OSPF or BGP to route the VTI address to the peer instead of static routes

D. Route-based VTI takes precedence over the Domain VPN. Troubleshoot the static route entries to insure that they are correctly pointing to the VTI gateway IP.

Answer: B

Question No: 9

To provide full connectivity upgrade status, use command cphaprob fcustat

Answer:

Question No: 10

You are responsible for the configuration of MegaCorpu2021s Check Point Firewall. You need to allow two NAT rules to match a connection. Is it possible? Give the BEST answer.

A. No, it is not possible to have more than one NAT rule matching a connection. When the firewall receives a packet belonging to a connection, it compares it against the first rule in the Rule Base, then the second rule, and so on. When it finds a rule that matches, it stops checking and applies that rule.

B. Yes, it is possible to have two NAT rules which match a connection, but only in using Manual NAT

(bidirectional NAT).

C. Yes, there are always as many active NAT rules as there are connections.

D. Yes, it is possible to have two NAT rules which match a connection, but only when using Automatic NAT (bidirectional NAT).

Answer: D

Question No: 11

Security Gateway R80 supports User Authentication for which of the following services? Select the response below that contains the MOST correct list of supported services.

A. SMTP, FTP, TELNET

B. SMTP, FTP, HTTP, TELNET

C. FTP, HTTP, TELNET

D. FTP, TELNET

Answer: C

Question No: 12

You have configured Automatic Static NAT on an internal host-node object. You clear the box Translate destination on client site from Global Properties > NAT. Assuming all other NAT settings in Global Properties are selected, what else must be configured so that a host on the Internet can initiate an inbound connection to this host?

A. No extra configuration is needed.

B. A proxy ARP entry, to ensure packets destined for the public IP address will reach the Security Gateway's external interface.

C. The NAT IP address must be added to the external Gateway interface anti-spoofing group.

D. A static route, to ensure packets destined for the public NAT IP address will reach the Gateway's internal interface.

Answer: D

Question No: 13

What is the purpose of the pre-defined exclusions included with SmartEvent R80?

A. To allow SmartEvent R80 to function properly with all other R71 devices.

B. To avoid incorrect event generation by the default IPS event definition; a scenario that may occur in deployments that include Security Gateways of versions prior to R71.

C. As a base for starting and building exclusions.

D. To give samples of how to write your own exclusion.

Answer: B

Question No: 14

You have created a Rule Base for firewall, websydney. Now you are going to create a new policy package with security and address translation rules for a second Gateway.

What is TRUE about the new packageu2021s NAT rules?

A. Rules 1, 2, 3 will appear in the new package.

B. Only rule 1 will appear in the new package.

C. NAT rules will be empty in the new package.

D. Rules 4 and 5 will appear in the new package.

Answer: A

Question No: 15

Which statements about Management HA are correct?

1) Primary SmartCenter describes first installed SmartCenter

2) Active SmartCenter is always used to administrate with SmartConsole

3) Active SmartCenter describes first installed SmartCenter

4) Primary SmartCenter is always used to administrate with SmartConsole

A. 1 and 4

B. 2 and 3

C. 1 and 2

D. 3 and 4

Answer: C

Question No: 16

You are about to integrate RSA SecurID users into the Check Point infrastructure. What kind of users are to be defined via SmartDashboard?

A. A group with generic user

B. All users

C. LDAP Account Unit Group

D. Internal user Group

Answer: A

100% Avant-garde Check Point 156-915.80 Questions & Answers shared by Allfreedumps, Get HERE: https://www.allfreedumps.com/156-915.80-dumps.html (New Q&As)