200-125 Exam Questions - Online Test

200-125 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

Our pass rate is high to 98.9% and the similarity percentage between our ccna 200 125 book study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco ccna 200 125 syllabus exam in just one try? I am currently studying for the Cisco ccna routing and switching 200 125 pdf exam. Latest Cisco 200 125 ccna pdf Test exam practice questions and answers, Try Cisco cisco ccna 200 125 Brain Dumps First.

P.S. Accurate 200-125 Q&A are available on Google Drive, GET MORE: https://drive.google.com/open?id=1jQmx5oxI6Dh5yoCIPQpEra2L4K5UYNUa

New Cisco 200-125 Exam Dumps Collection (Question 3 - Question 12)

Question No: 3

In which circumstance are multiple copies of the same unicast frame likely to be transmitted in a switched LAN?

A. during high traffic periods

B. after broken links are re-established

C. when upper-layer protocols require high reliability

D. in an improperly implemented redundant topology

E. when a dual ring topology is in use

Answer: D

Explanation:

If we connect two switches via 2 or more links and do not enable STP on these switches then a loop (which creates multiple copies of the same unicast frame) will occur. It is an example of an improperly implemented redundant topology.

Question No: 4

Refer to the exhibit.

A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three.)

A. host A IP address: 192.168.1.79

B. host A IP address: 192.168.1.64

C. host A default gateway: 192.168.1.78

D. host B IP address: 192.168.1.128

E. host B default gateway: 192.168.1.129

F. host B IP address: 192.168.1.190

Answer: A,C,F

Explanation:

Itu2021s a u201crouter-on-a-sticku201d configuration. Which means each host in the VLAN must corresponds with the VLAN configured on the sub-interfaces.

VLAN 10 is configured on fa0/0.10 and VLAN 20 on fa0/0.20. So each hosts in VLAN 10 must use fa0/0.10 IP address as their default gateway, each hosts must also be in the same subnet as fa0/0.10 IP u2013 same with hosts in VLAN 20.

So find out the usable IP addresses on each sub-interfaces u2013 for 192.168.1.78 /27: 192.168.1.65 u2013 .94 and for 192.168.1.130 /26: 192.168.1.128 u2013 .190.

Host A (using port 6 u2013 VLAN 10) must use IP 192.168.1.79, default gateway 192.168.1.78. Host B (using port 9 u2013 VLAN 20) must use IP 192.168.1.190, default gateway 192.168.1.130.

Question No: 5

What will be the result if the following configuration commands are implemented on a Cisco switch?

Switch(config-if)# switchport port-security

Switch(config-if)# switchport port-security mac-address sticky

A. A dynamically learned MAC address is saved in the startup-configuration file.

B. A dynamically learned MAC address is saved in the running-configuration file.

C. A dynamically learned MAC address is saved in the VLAN database.

D. Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.

E. Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.

Answer: B

Explanation:

In the interface configuration mode, the command switchport port-security mac-address sticky enables sticky learning. When entering this command, the interface converts all the dynamic secure MAC addresses to sticky secure MAC addresses.

Question No: 6

What levels will be trapped if the administrator executes the command router(config)# logging trap 4 (Choose four)

A. Emergency

B. Notice

C. Alert

D. Error

E. Warning

Answer: A,C,D,E

Explanation:

The Message Logging is divided into 8 levels as listed below: Level Keyword Description

0 emergencies System is unusable 1 alerts Immediate action is needed 2 critical Critical conditions exist

3 errors Error conditions exist

4 warnings Warning conditions exist

5 notification Normal, but significant, conditions exist 6 informational Informational messages

7 debugging Debugging messages

If you specify a level with the u201clogging trap levelu201d command, that level and all the higher levels will be logged. For example, by using the u201clogging trap 4 command, all the logging of emergencies, alerts, critical, errors, warnings will be logged.

Question No: 7

Refer to the exhibit.

If the devices produced the given output, what is the cause of the EtherChannel problem?

A. SW1's Fa0/1 interface is administratively shut down.

B. There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

C. There is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

D. There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

Answer: D

Explanation:

You must configure all interfaces in an EtherChannel to operate at the same speeds and duplex modes. Based on the output shown, SW1 is configured to run at 10Mb while SW2 is operating at 100 Mb.

Question No: 8

What are the three things that the Netflow uses to consider the traffic to be in a same flow? (Choose three)

A. IP address

B. Interface name

C. Port numbers

D. L3 protocol type

E. MAC address

Answer: A,C,D

Explanation:

What is an IP Flow?

Each packet that is forwarded within a router or switch is examined for a set of IP packet attributes. These attributes are the IP packet identity or fingerprint of the packet and determine if the packet is unique or similar to other packets.

Traditionally, an IP Flow is based on a set of 5 and up to 7 IP packet attributes. IP Packet attributes used by NetFlow:

+ IP source address

+ IP destination address

+ Source port

+ Destination port

+ Layer 3 protocol type

+ Class of Service

+ Router or switch interface

Question No: 9

How does using the service password-encryption command on a router provide additional security?

A. by encrypting all passwords passing through the router

B. by encrypting passwords in the plain text configuration file

C. by requiring entry of encrypted passwords for access to the device

D. by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges

E. by automatically suggesting encrypted passwords for use in configuring the router

Answer: B

Explanation:

By using this command, all the (current and future) passwords are encrypted. This command is primarily useful for keeping unauthorized individuals from viewing your password in your configuration file

Question No: 10

What command visualizes the general NetFlow data on the command line?

A. show ip flow export

B. show ip flow top-talkers

C. show ip cache flow

D. show mls sampling

E. show mls netflow ip

Answer: C

Explanation:

The following is an example of how to visualize the NetFlow data using the CLI. There are three methods to visualize the data depending on the version of Cisco IOS Software. The traditional show command for NetFlow is "show ip cache flow" also available are two forms of top talker commands. One of the top talkers commands uses a static configuration to view top talkers in the network and another command called dynamic top talkers allows real-time sorting and aggregation of NetFlow data. Also shown is a show MLS command to view the hardware cache on the Cisco Catalyst 6500 Series Switch.

The following is the original NetFlow show command used for many years in Cisco IOS Software. Information provided includes packet size distribution; basic statistics about number of flows and export timer setting, a view of the protocol distribution statistics and the NetFlow cache.

The u201cshow ip cache flowu201d command displays a summary of the NetFlow accounting statistics.

Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-netflow/prod_white_paper0900aecd80406232.html

Question No: 11

Scenario

Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.

You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.

An OSPF neighbor adjacency is not formed between R3 in the main office and R6 in the Branch3 office. What is causing the problem?

A. There is an area ID mismatch.

B. There is a PPP authentication issue; the username is not configured on R3 and R6.

C. There is an OSPF hello and dead interval mismatch.

D. The R3 router ID is configured on R6.

Answer: D

Explanation:

Using the show running-config command we see that R6 has been incorrectly configured with the same router ID as R3 under the router OSPF process.

Question No: 12

Refer to exhibit.

A network administrator cannot establish a Telnet session with the indicated router. What is the cause of this failure?

A. A Level 5 password is not set.

B. An ACL is blocking Telnet access.

C. The vty password is missing.

D. The console password is missing.

Answer: C

Explanation:

The login keyword has been set, but not password. This will result in the u201cpassword

required, but none setu201d message to users trying to telnet to this router.

P.S. Easily pass 200-125 Exam with Surepassexam Accurate Dumps & pdf vce, Try Free: https://www.surepassexam.com/200-125-exam-dumps.html (890 New Questions)